Original TLE6208 TLE6208-3G / 6G SOP16

Original  TLE6208 TLE6208-3G / 6G SOP16 

Car Doors And Windows Control Driver

Models : TLE6208-3g SOP16

Manufacturer : Infineon

Product Categories : Integrated Circuits (ICs), Transistor, MOSFET 

Package/Case : SOP16

Reference To Part : TLE6208-3g SOP16

Substitute : TLE6208-3g SOP16

Found : Car Doors And Windows Control Driver

Package Include :

1 X TLE6208-3g SOP16

TLE6208-3g Automotive electronic IC is car engine control computer drive chip, it is easily damaged parts on Auto ECU controller board,  TLE6208-3g Car engine control unit electronic IC, and the ECU Integrated Circuit IC for car electronic repair.

Three Half-Bridges

• Optimized for DC motor management applications

• Delivers up to 0.6 A continuous, 1.2 A peak current

• RDS ON; typ. 0.8 ?, @ 25 °C per switch

• Output: short circuit protected and diagnosis

• Overtemperature-Protection with hysteresis and diagnosis

• Standard SPI-Interface/Daisy chain capable

• Very low current consumption in stand-by (Inhibit) 

• mode (typ. 10 µA for power and 2 µA for logic supply, @ 25 °C)

• Over- and Undervoltage-Lockout

• CMOS/TTL compatible inputs with hysteresis

• No crossover current

• Internal clamp diodes

• Enhanced power P-DSO-Package

1.3 Pin Definitions and Functions

Pin No. Symbol Function

1 GND Ground; Reference potential; internal connection to pin 7, 8 and 14;

cooling tab; to reduce thermal resistance place cooling areas on PCB

close to these pins.

2 OUT3 Halfbridge-Output 3;

Internally contected to Highside-Switch 3 and Lowside-Switch 3. The

HS-Switch is a Power-MOS open drain with internal reverse diode;

The LS-Switch is a Power-MOS open source with internal reverse

diode; no internal clamp diode or active zenering;

short circuit protected and open load controlled.

3 VS Power Supply;

needs a blocking capacitor as close as possible to GND Value: 22 µF

electrolytic in parallel to 220 nF ceramic.

5 DI Serial Data Input; receives serial data from the control device; serial

data transmitted to DI is an 16bit control word with the Least

Significant Bit (LSB) being transferred first: the input has an active

pull down and requires CMOS logic level inputs;

DI will accept data on the falling edge of CLK-signal;

see Table Input Data Protocol.

4 CSN Chip-Select-Not Input; CSN is an active low input; serial

communication is enabled by pulling the CSN terminal low; CSN

input should only be transitioned when CLK is low; CSN has an

internal active pull up and requires CMOS logic level inputs.

6 CLK Serial Clock Input; clocks the shiftregister; CLK has an internal

active pull down and requires CMOS logic level inputs.

7, 8, 14 GND Ground; see pin 1.

9 DO Serial-Data-Output; this 3-state output transfers diagnosis data to

the control device; the output will remain 3-stated unless the device

is selected by a low on Chip-Select-Not (CSN);

see Table Diagnosis Data Protocol.

10 INH Inhibit Input; has an internal pull down;

device is switched in standby condition by pulling the INH terminal

low.

11 VCC Logic Supply Voltage;

needs a blocking capacitor as close as possible to GND;

Value: 10 µF electrolytic in parallel to 220 nF ceramic.

12 OUT1 Halfbridge-Output 1; see pin 2.

13 OUT2 Halfbridge-Output 2; see

 

Agus Yulianto

Perum Puri Astapada Indah 2 Rt:08 Rw.03 Blok K No:6 
Plosogeneng Kec .Jombang, Kab.Jombang, Jawa Timur 61416
Hp.  0813-3278-7811 Kantor  0321-852845

Alamat Lokasi toko/rumah Google map
https://goo.gl/maps/7NZ4HMSYvvJ2

Web  :www.obd2jombang.com

Blog 
http://ToolsTeknik.blogspot.co.id
http://Obd2Jombang.blogspot.co.id

Tokopedia
https://www.tokopedia.com/obd2

Bukalapak
https://www.bukalapak.com/agusyulianto

Facebook Agus Yuli Obd Jatim
https://www.facebook.com/obd99